| RB3-0067-000CN |
Pulley roller (accommodates one feed belt) - Small black roller approximately 1.59cm (0.625-inch) long with one ball type pulley - Mounts just behind the tranfer roller |
| RB3-0089-000CN |
Top cover rack arm - Black plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open - Mounts on the right side of the top cover door |
| RB3-0090-000CN |
Rack slide - White plastic piece with gear teeth layed out in rack form on both sides - Part of the mechanism that disengages the imaging drum/transfer assembly cams |
| RB3-0091-000CN |
16 tooth gear - Black plastic gear with large stop tooth and shaft lock tab - Used as part of the mechanism to disengage the drive cams for the imaging drum/transfer assembly - Mounts on the inside of the right side metal chassis assembly |
| RB3-0092-000CN |
15 tooth gear with drive shaft (black plastic) - Used as part of the mechanism to disengage the drive cams for the imaging drum/transfer assembly - Mounts on the right side metal chassis frame |
| RB3-0102-000CN |
Front inner cover (blue plastic) - Mounts on the front frame above the multi-purpose input tray |
| RB3-0103-000CN |
Front lower cover (blue plastic) - Front lower strip below the multi-purpose input tray - Has recessed area for the printer logo |
| RB3-0104-000CN |
Roller cover - Covers the multi-purpose paper pick-up roller assembly - Mounts in the lower portion of the front frame assembly |
| RB3-0105-000CN |
Center support frame (black plastic) - Support structure for the paper pick-up roller, feed roller, and paper sensors - Mounts to the top front of both |
| RB3-0106-000CN |
Left side frame/cover (Quartz Gray plastic) - Left side cover and paper tray guide - For the base on the 250 sheet input tray assembly |
| RB3-0108-000CN |
Metal support cross-brace - Mounts on the top rear of the left and right support frame/cover assemblies - For the base on the 250 sheet input tray assembly |
| RB3-0109-000CN |
Front cover for the 250 sheet paper cassette tray (blue plastic) - Has molded in paper loading instructions and a "2" on the front - |
| RB3-0111-000CN |
Paper flag - Plastic rod with paper sensing flag on one end and sensor activator flag on the other - Senses paper coming from the multi-purpose front input tray (tray 1) |
| RB3-0119-000CN |
Grounding plate - Grounds the paper pick-up solenoid cover to the right side metal chassis |
| RB3-0120-000CN |
Solenoid cover (Steel) - Cover for the multi-purpose tray pickup roller solenoid (SL92) |
| RB3-0121-000CN |
Right retaining spring - Helps to secure and ground the imaging drum/transfer assembly in the printer - Mounts on the upper right side of the front frame assembly |
| RB3-0122-000CN |
Left retaining spring - Helps to secure the imaging drum/transfer assembly in the printer - Mounts on the upper left side of the front frame assembly |
| RB3-0129-000CN |
Feed roller assembly - Includes the metal shaft and two small rubber rollers - Feeds paper from the paper cassette (or tray 3 below) into the printer - |
| RB3-0130-000CN |
Shaft mounted sensor flag (black plastic) - For the paper out sensor - Mounts on the paper pick-up roller drive shaft - For the base on the 250 sheet input tray assembly |
| RB3-0132-000CN |
Mechanical sensor flag (black plastic) - For the paper feed sensor - Mounts on top of the center frame assembly - For the base on the 250 sheet input tray assembly |
| RB3-0135-000CN |
Test print flag (black lever) - Used to activate the print engine test switch - Mounts in a metal holder in the upper left of the front frame assembly |
| RB3-0136-000CN |
Solenoid cover/magnetic shield - Mounts on the right end of the center frame assembly (over the pick-up solenoid) - For the base on the 250 sheet input tray assembly |
| RB3-0137-000CN |
Grounding plate - Grounds the paper feed roller - Mounts towards the right end of the center frame assembly - For the base on the 250 sheet input tray assembly |
| RB3-0140-000CN |
Left cover plate (Quartz Gray plastic) - Mounts on the left side of the center frame - For the base on the 500 sheet input tray assembly |
| RB3-0141-000CN |
Right cover plate (Quartz Gray plastic) - Mounts on the Right side of the center frame - For the base on the 500 sheet input tray assembly |
| RB3-0160-000CN |
Paper pick-up roller (D-shaped) - Mounts on the paper pick up roller assembly for the multi-purpose front input tray (tray 1) |
| RB3-0161-000CN |
Paper pick-up roller assembly - Includes the `D` shaped rubber roller on a plastic shaft - Mounts in the lower center of the center frame assembly - |
| RB3-0165-000CN |
Top inner cover (black plastic) - Covers the back half of the pressure roller arms and springs - For the base on the 250 sheet input tray assembly |
| RB3-0166-000CN |
Bottom inner cover (black plastic) - Mounts on the bottom of the center frame assembly in the base on the 250 sheet input tray assembly - One covers the paper feed sensor |
| RB3-0176-000CN |
Face-Up output tray door (ONLY) - Pull-down tray door for face-up output - Mounts to the top of the locking bracket on the fusing assembly |
| RB3-0178-000CN |
Right side lock release lever - Part of locking system used to secure the fusing assembly in the printer |
| RB3-0179-000CN |
Left side lock release lever - Part of locking system used to secure the fusing assembly in the printer |
| RB3-0282-000CN |
Inner cover - Covers the small interconnecting PC board and the connector for tray 3 - Mounts on top of the right side support frame/cover assembly - |
| RB3-0283-000CN |
Inner cover - Covers the connector that interconnects the input tray base to the printer - Mounts on the bottom of the right side support frame/cover assembly - |
| RB3-0286-000CN |
Contact plate - Runs between the shaft on the registration roller and the metal entrance guide assembly |
| RB3-0304-040 |
Front caster - |
| RB3-0304-040CN |
Front caster - |
| RB3-0352-000 |
Fan grounding plate and fan housing |
| RB3-0352-000CN |
Fan grounding plate and fan housing |
| RB3-0431-000 |
Sensor flag lever - Paper feed sensor arm |
| RB3-0431-000CN |
Sensor flag lever - Paper feed sensor arm |
| RB3-0441-000 |
Tray cover - Rear tray cover for 500 sheet universal paper tray |
| RB3-0441-000CN |
Tray cover - Rear tray cover for 500 sheet universal paper tray |
| RB3-0443-000 |
Lever link - Mechanical link between paper sensor flag and sensor holder |
| RB3-0443-000CN |
Lever link - Mechanical link between paper sensor flag and sensor holder |
| RB3-0444-000 |
Sensor holder - Holds sensor used with paper sensor flag |
| RB3-0444-000CN |
Sensor holder - Holds sensor used with paper sensor flag |
| RB3-0905-000 |
Paper sensor arm - Flag for registration photosensor |
| RB3-0905-000CN |
Paper sensor arm - Flag for registration photosensor |
| RB9-0684-000 |
Fusing assembly pressure roller |
| RB9-0684-000CN |
Fusing assembly pressure roller |
| RB9-0695 |
Separation pad - Moveable pad on front of Optional 250 sheet paper tray (C4793A) |
| RB9-0695-020 |
Separation pad - Moveable pad on front of Optional 250 sheet paper tray (C4793A) |
| RB9-0695-020CN |
Separation pad - Moveable pad on front of Optional 250 sheet paper tray (C4793A) |
| RC1-0003-000 |
Toner cartridge arm - Mechanical link between main drive assembly and toner cartridge release mechanism |
| RC1-0003-000CN |
Toner cartridge arm - Mechanical link between main drive assembly and toner cartridge release mechanism |
| RC1-0019-000 |
Inner right front cover |
| RC1-0019-000CN |
Inner right front cover |
| RC1-0060-000 |
Paper feed sensor flag for Tray 1 |
| RC1-0060-000CN |
Paper feed sensor flag for Tray 1 |
| RC1-0061-000 |
Torsion spring |
| RC1-0061-000CN |
Torsion spring |
| RC1-0070-000CN |
Pressure roller - Roller in fusing assembly that provides pressure for media against the fusing roller |
| RC1-0153-010 |
Right side Tray 2 paper cassette guide |
| RC1-0153-010CN |
Right side Tray 2 paper cassette guide |
| RC1-0161-000 |
Paper size sensing flag - White plastic arm used as mechanical link to tray size sensor PC Board - Three used per sensing assembly |
| RC1-0161-000CN |
Paper size sensing flag - White plastic arm used as mechanical link to tray size sensor PC Board - Three used per sensing assembly |
| RC1-0198-000 |
Tension spring - Provides tension for lifter drive assembly |
| RC1-0198-000CN |
Tension spring - Provides tension for lifter drive assembly |
| RC1-0206-000 |
Bushing - On right side of paper pickup drive assembly |
| RC1-0206-000CN |
Bushing - On right side of paper pickup drive assembly |
| RC1-0208-000CN |
Paper sensor flag holder |
| RC1-0209-000 |
Paper sensor flag for Tray 2 paper pickup assembly |
| RC1-0209-000CN |
Paper sensor flag for Tray 2 paper pickup assembly |
| RC1-0210-000 |
Feeder roller shaft - Axel for Tray 2 feed roller |
|