| RB2-8124-000CN |
ETB socket - Socket that right side of ETB fits into |
| RB2-8151-020CN |
Pressure arm |
| RB2-8195-000CN |
Cartridge pressure lever |
| RB2-8213-000CN |
Spring rod - Provides mechanical link for spring pressure to assist opening Tray1/MP tray - 2 used |
| RB2-8225-000CN |
Drum drive interlock plate |
| RB2-8239-000CN |
Developer disengagement plate - Mechanical link that disengages developer from drum |
| RB2-8246-000CN |
Laser scanner support spring - Supports laser scanner module - Three used |
| RB2-8250-000CN |
Test print arm - External test print button/rod |
| RB2-8255-000CN |
Grounding plate - Provides ground for developer units |
| RB2-8349-000CN |
Paper size arm - Senses paper size in paper tray - 3 used |
| RB2-8498-030CN |
Paper sensor flag in fuser assembly |
| RB2-8540-000CN |
Sensor support bracket - Black plastic piece that holds photo sensors PS12 and PS13 |
| RB2-8590-000CN |
Left cover - Left side of printer cover |
| RB2-8591-000CN |
Side cover - Right side of printer cover |
| RB2-8592-000CN |
Rear cover - Rear of printer cover |
| RB2-8596-000CN |
Air filter on upper left side |
| RB2-8597-000CN |
Air filter at top rear of printer - Formatter fan air filter |
| RB2-8751-000 |
Face-up tray release handle |
| RB2-8769-000 |
ADF pickup roller |
| RB2-8793-020 |
Clear Mylar sheet |
| RB2-9808-000CN |
Bushing/shaft retainer assembly (Black plastic) - Holds the rotation drive shaft in the right side plate of the toner cartridge carousel (rotary) assembly |
| RB2-9809-000CN |
Bushing/shaft retainer assembly (White plastic) - Holds the rotation drive shaft in the left side plate of the toner cartridge carousel (rotary) assembly |
| RB2-9903-000CN |
Cable guide (Quartz Gray plastic) - Protects and supports the upper cable assembly - Mounts to the right rear on the laser/scanner support assembly |
| RB2-9904-000CN |
Airflow Guide (duct) - Black plastic insert piece which runs the width of the printer and has an air flow hole on right side - Directs air flow from the fan on the left side of the printer to the fusing assembly - Snap locks in center rear of printer |
| RB2-9905-000CN |
Torsion spring - Provides pressure for the upper top bin output pressure rollers (two used) |
| RB2-9906-000CN |
Torsion spring - Provides pressure for the lower top bin output pressure rollers (two used) |
| RB2-9908-000CN |
Pressure roller (small black hard plastic `disked` roller) - Rides up against the upper top bin output roller on the top rear of the printer (two used) |
| RB2-9909-000CN |
Pressure roller (small black hard plastic `solid` roller) - Rides up against the lower top bin output roller on the middle rear of the printer (two used) |
| RB2-9912-000CN |
Top output bin guide - Small curvered ribbed black plastic piece - Snaps on the rear of the printer just below the upper top bin output roller (two used) |
| RB2-9916-000CN |
Mounting plate - For the engaging motor (PM704) - Mounts on the upper left side of the rear frame assembly |
| RB2-9924-000CN |
Sensor assembly mounting holder - For mounting the leading edge paper sensor for the fusing assembly (PS720) - Mounts to the underside of the middle frame assembly |
| RB2-9925-000CN |
Sensor arm and flag - Activates the photosensor (Does NOT include the roller) - For the Leading edge paper sensor for the fusing assembly (PS720) - Protrudes up through the feed plate on the middle frame assembly |
| RB2-9932-000CN |
RFI shield - Parallel wire form mounted over the fan - Mounts on the fan air duct assembly on the left side of the printer |
| RB2-9942-000CN |
Grounding plate - Provides grounding for the top-of-page sensor and shielding for the density sensor boards - Mounts on the top left of the front frame assembly |
| RB2-9952-000CN |
Tray 1 flag spring - Provides torsion for the tray 1 paper sensor flag - Mounts in the lower portion of the front frame assembly |
| RB2-9954-000CN |
Paper feed guide (black plastic) - Mounts to the left of the separation pad assembly on the lower front frame assembly |
| RB2-9955-000CN |
Paper feed guide (black plastic) - Mounts to the right of the separation pad assembly on the lower front frame |
| RB2-9960 |
Separation pad assembly - Includes the gray plastic frame with the rubber insert strip - For the cassette on the 250 sheet and 500 sheet input tray assemblies |
| RB2-9960-000 |
Separation pad assembly - Includes the gray plastic frame with the rubber insert strip |
| RB2-9960-000CN |
Separation pad assembly - Includes the gray plastic frame with the rubber insert strip - For the cassette on the 250 sheet and 500 sheet input tray assemblies |
| RB2-9963-000CN |
Separation pad support - Pivoting `L` shaped metal support frame (Does NOT include the separation pad assembly) - For the cassette on the 250 sheet input tray assembly |
| RB3-0006-000CN |
Holder - Housing for the fusing connector assembly - Mounts on the bottom pan of the printer |
| RB3-0007-000CN |
Insulating sheet (Transparent plastic) - Mounts between the bottom pan and the high and low voltage power supply boards |
| RB3-0009-000CN |
Static eliminator ground plate - Right angled metal piece with small teeth on top edge - Mounts from underneath on the middle frame assembly just behind the pulley rollers |
| RB3-0010-000CN |
Feed plate - Center metal plate with slots that the ribs on the middle frame assembly go through - Mounts behind the transfer roller on the middle frame assembly |
| RB3-0011-000CN |
Feed drive shaft - Long shaft with eight feed belt ball type pulleys and one ribbed feed guide drive belt pulley - Mounts behind the transfer roller on the middle frame assembly |
| RB3-0012-000CN |
Belt roller - Small black oval shaped roller approximately 1-3/4 inches long - Mounts toward the center of the metal feed plate on the middle frame assembly |
| RB3-0014-000CN |
Bushing assembly (black plastic bushing with small guide roller on top) - Holds the right end of the transfer roller assembly in the bottom frame assmebly |
| RB3-0015-000CN |
Compression spring - Provides upward pressure for the left transfer roller bushing |
| RB3-0016-000CN |
Electrical contact spring - Spring steel wire with compression springs formed on both ends - One end provides upward pressure on the right bushing for the transfer roller - Connects to high voltage board |
| RB3-0019-000CN |
Toner catch tray (Curved black plastic piece) - Holds residual toner from photosensitive drum - Mounts just below the toner cartridge carousel on the bottom frame assembly |
| RB3-0022-000CN |
22 tooth gear - Small black gear with diagonally cut teeth - Idler gear between the transfer roller assembly and the feed drive shaft - Mounts on the left side of the middle frame assembly |
| RB3-0023-000CN |
Interlock switch holder (Quartz Gray plastic) - Mounts to the laser/scanner support assembly - Towards the left rear of the printer |
| RB3-0025-000CN |
Airflow guide (duct) assembly and fan holder bracket (Quartz Gray plastic) - Mounts on the left metal side frame assembly |
| RB3-0028-000CN |
Left side cover ONLY (Quartz Gray plastic) - Does not include any attaching parts - Mounts on left side of printer |
| RB3-0030-000CN |
Upper rear cover (Quartz Gray plastic) - Mounts on the upper rear of the printer above the face-up output tray door |
| RB3-0032-000CN |
Face-down paper output cover (L-Shaped blue plastic) - Serves as the rear of the tray for the face-down output tray on top of the printer - Mounts in the upper rear of the printer mechanism |
| RB3-0033-000CN |
DIMM memory door (Quartz Gray perforated plastic) - Access door for adding or removing printer memory - Mounts on the right side cover |
| RB3-0035-000CN |
Interface bezel (Quartz Gray plastic) - Vertical cover that surronds the interface connectors - Mounts on the right rear of the printer |
| RB3-0037-000CN |
Power switch rod - Goes between the power button and the power switch on the low voltage power supply board - Mounts on the left side cover |
| RB3-0042-000CN |
Electrical contact spring - Mounts on the middle frame assembly behind the transfer roller - Of the four similar springs, this one is next to the one on the far left - Connects to high voltage board |
| RB3-0043-000CN |
Electrical contact spring - Mounts on the middle frame assembly behind the transfer roller - Of the four similar springs, this one is on the far right - Connects to high voltage board |
| RB3-0044-000CN |
Electrical contact spring - (Front) Provides high voltage to the toner cartridge via a cable assembly and connection through the carousel plate assembly - Connects to the high voltage board |
| RB3-0045-000CN |
Electrical contact spring - (Rear) Provides high voltage to the toner cartridge via a cable assembly and connection through the carousel plate assembly - Connects to the high voltage board |
| RB3-0046-000CN |
Electrical contact spring - Mounts on the middle frame assembly behind the transfer roller - Of the four similar springs, this one is just to the left of the one on the far right - Connects to high voltage board |
| RB3-0047-000CN |
Electrical contact spring - Mounts on the underside of the middle frame assembly - Connects to high voltage board |
| RB3-0048-000CN |
Electrical contact spring - Mounts on the middle frame assembly behind the transfer roller - Of the four similar springs, this one is on the far left - Connects to the high voltage board |
| RB3-0052-000CN |
Gear Cover (Small black plastic cover) - Protects the idler gear for the transfer roller - Mounts toward the left side of the middle frame assembly |
| RB3-0056-000CN |
Insulating sheet (Transparent plastic) - Mounts to the underside of the middle frame assembly |
| RB3-0057-000CN |
Transfer slide plate - Small `U` shaped metal insert plates - Mount in the bushing wells for the transfer roller on the middle frame assembly (2 Used) |
| RB3-0060-000CN |
Idler gear shaft (Short metal rod) - Shaft for the transfer and feed drive idler roller - Mounts on the left side of the middle frame assembly |
| RB3-0061-000CN |
Pulley roller (accommodates three feed belts) - Small black roller approximately 3.49cm (1.75-inches) long with three ball type pulleys - Mounts just behind the tranfer |
| RB3-0062-000CN |
PC board support (black plastic holder) - For mounting the small sub-high voltage board above the high voltage board |
| RB3-0063-000CN |
Feed belt - Small black rubber belt approximately 1/8 inch wide with little `A` shaped ribs on it - Goes between the feed drive roller and the pulley rollers (8 used) |
| RB3-0065-000CN |
Ground plate (Copper clad metal spring) - Mounts on the left side of the middle frame below the entrance guide assembly |
|