| RA1-8419-000 |
Tray Extender - U-Shaped Wire Form on Switchback Assy Output |
| RA2-0420-000 |
Sensor Lever - Spring Attaches to it - Actuates Photosensor 402 Sensor Lever |
| RA2-0420-000CN |
Sensor Lever - Spring Attaches to it - Actuates Photosensor 402 Sensor Lever |
| RA2-0448-000 |
Front door (Right side) hinge pin - Transparent in color |
| RA2-0448-000CN |
Front door (Right side) hinge pin - Transparent in color |
| RA2-0831-000 |
Fan bearing - For older (Japan servo) upper fan ONLY |
| RA2-1999-000 |
Corner Tab - for Universal Cassette - Prevents Paper Wrinkling and Misfeeds |
| RA2-2061-000 |
Front Cover (L-Shaped) - Small Cover on the Front of the Duplexer (Under the LaserJet) - Has an Arrow on it |
| RA2-2072-000 |
Timing Belt - Between the Two Holding Tray Rollers - Goes on the Left Side of the Paper Holding Area (Under the LaserJet) of the Duplexer |
| RA2-2072-000CN |
Timing Belt - Between the Two Holding Tray Rollers - Goes on the Left Side of the Paper Holding Area (Under the LaserJet) of the Duplexer |
| RA2-2083-000 |
Static Brush - Mounts to the Bottom of the Lower Feed Guide (Towards the Bottom of the Switchback Area of the Duplexer) |
| RA2-2083-000CN |
Static Brush - Mounts to the Bottom of the Lower Feed Guide (Towards the Bottom of the Switchback Area of the Duplexer) |
| RA2-2087-000 |
Deflector Linkage - Connects Solenoid (SL1) to Duplex Switchback Paper Deflector Assembly |
| RA2-2087-000CN |
Deflector Linkage - Connects Solenoid (SL1) to Duplex Switchback Paper Deflector Assembly |
| RA2-2088-000 |
Switchback guide - Large ribbed piece in the top of the switchback area of the duplexer |
| RA2-2088-000CN |
Switchback guide - Large ribbed piece in the top of the switchback area of the duplexer |
| RA2-2089-000 |
Roller Holder - Pinch Roller Holder - Four Used |
| RA2-2089-000CN |
Roller Holder - Pinch Roller Holder - Four Used |
| RA2-2090-000 |
Switchback deflector (Shaft with curved deflector fingers) - Attaches to the rear of the switchback guide (in the top of the duplexer) |
| RA2-2090-000CN |
Switchback deflector (Shaft with curved deflector fingers) - Attaches to the rear of the switchback guide (in the top of the duplexer) |
| RA2-2093-000 |
Pinch Roller - Top of Switchback Guide - 4 Used |
| RA2-2093-000CN |
Pinch Roller - Top of Switchback Guide - 4 Used |
| RA2-2094-000 |
Upper feed guide - Upper curved paper feed guide |
| RA2-2094-000CN |
Upper feed guide - Upper curved paper feed guide |
| RA2-2095-000 |
Lower guide - Lower curved paper feed guide |
| RA2-2095-000CN |
Lower guide - Lower curved paper feed guide |
| RA2-2096-000 |
Left Cover - Small Cover on the Left Side of the Duplexer (Under the LaserJet) - Viewed from the Front of the Printer |
| RA2-2097-000 |
Right Cover - Small Cover on the Right Side of the Duplexer (Under the LaserJet) - Viewed from the Front of the Printer |
| RA2-2098-000 |
Lower Rear Cover - Small Cover Under the Switchback Area of the Duplexer |
| RA2-2100-000 |
Locking Latch - on the Top of the Duplexer Rear Cover |
| RA2-2102-000 |
Guide Roller - Non-Spring Loaded Rollers on Front of Switchback Guide - Three Used |
| RA2-2102-000CN |
Guide Roller - Non-Spring Loaded Rollers on Front of Switchback Guide - Three Used |
| RA2-2112-000 |
Cable Cover - Protects Cable on Right Side of Duplexer Switchback Assembly |
| RA2-2112-000CN |
Cable Cover - Protects Cable on Right Side of Duplexer Switchback Assembly |
| RA2-2118-000 |
Paper drive roller (Shaft with four rubber rollers on it) - Mounts in the rear of the switchback area of the duplexer (Rollers extend through cut outs in the rear support frame) |
| RA2-2118-000CN |
Paper drive roller (Shaft with four rubber rollers on it) - Mounts in the rear of the switchback area of the duplexer (Rollers extend through cut outs in the rear support frame) |
| RA2-2119-000 |
Paper deflector assembly (Shaft with curved deflector fingers) - Attaches to the front of the switchback guide (in the top of the duplexer) - Solenoid activated |
| RA2-2119-000CN |
Paper deflector assembly (Shaft with curved deflector fingers) - Attaches to the front of the switchback guide (in the top of the duplexer) - Solenoid activated |
| RA2-2124-000 |
Paper drive roller (Shaft with four rubber rollers on it) - Mounts in the top center in the switchback area of the duplexer |
| RA2-2124-000CN |
Paper drive roller (Shaft with four rubber rollers on it) - Mounts in the top center in the switchback area of the duplexer |
| RA2-2126-000 |
Static Brush - Mounts in the Front of the Paper Holding Area (Under the LaserJet) of the Duplexer |
| RA2-2126-000CN |
Static Brush - Mounts in the Front of the Paper Holding Area (Under the LaserJet) of the Duplexer |
| RA2-2231-000 |
Front Cover (L-Shaped) - Small Cover on the Front of the Duplexer (Under the LaserJet) - Has an Arrow on it |
| RA2-2231-000CN |
Front Cover (L-Shaped) - Small Cover on the Front of the Duplexer (Under the LaserJet) - Has an Arrow on it |
| RA2-2232-000 |
Left Cover - Small Cover on the Left Side of the Duplexer (Under the LaserJet) - Viewed from the Front of the Printer |
| RA2-2232-000CN |
Left Cover - Small Cover on the Left Side of the Duplexer (Under the LaserJet) - Viewed from the Front of the Printer |
| RA2-2233-000 |
Right Cover - Small Cover on the Right Side of the Duplexer (Under the LaserJet) - Viewed from the Front of the Printer |
| RA2-2233-000CN |
Right Cover - Small Cover on the Right Side of the Duplexer (Under the LaserJet) - Viewed from the Front of the Printer |
| RA2-2237-000 |
Lower Rear Cover - Small Cover Under the Switchback Area of the Duplexer |
| RA2-2237-000CN |
Lower Rear Cover - Small Cover Under the Switchback Area of the Duplexer |
| RA2-2408-000 |
Bottom bin tray |
| RA2-2408-000CN |
Bottom bin tray |
| RA2-2439-000 |
Positioning Pin - Keeps Right Cover Positioned Correctly |
| RA2-2439-000CN |
Positioning Pin - Keeps Right Cover Positioned Correctly |
| RA2-2484-000 |
Bin Full Sensor Arm - Attached to Face Up Bin Sensor Flag |
| RA2-2484-000CN |
Bin Full Sensor Arm - Attached to Face Up Bin Sensor Flag |
| RA2-2485-000 |
Sensor flag - Optical sensor for bin full sensor |
| RA2-2485-000CN |
Sensor flag - Optical sensor for bin full sensor |
| RA2-2487-000 |
Reversing Tray - Output Tray - Face-up |
| RA2-2487-000CN |
Reversing Tray - Output Tray - Face-up |
| RA2-2500-000 |
Support plate - Supports empty bin sensor PCA |
| RA2-2500-000CN |
Support plate - Supports empty bin sensor PCA |
| RA2-2505-000 |
Output bin roller bushing |
| RA2-2505-000CN |
Output bin roller bushing |
| RA2-2512-000 |
Release handle - Latch lever handle |
| RA2-2512-000CN |
Release handle - Latch lever handle |
| RA2-2513-000 |
Tension spring - Provides tension for latch handle |
| RA2-2513-000CN |
Tension spring - Provides tension for latch handle |
| RA2-2527-000 |
Stopper plate - Limits travel of right cover |
| RA2-2527-000CN |
Stopper plate - Limits travel of right cover |
| RA2-2531-000 |
Release latch handle cover |
| RA2-2531-000CN |
Release latch handle cover |
| RA2-2541-000 |
Motor cover - Reversing mechanism motor cover plate |
| RA2-2541-000CN |
Motor cover - Reversing mechanism motor cover plate |
| RA8-2456-000 |
Rubber Foot - for Bottom of Printer (4 Used) |
|