| RA0-1089-000 |
17 tooth gear - Mounts on the end of the face-up output roller - Center gear of three gears on the fusing assembly |
| RA0-1089-000CN |
Mounts on the end of the face-up output roller - Center gear of three gears on the fusing assembly |
| RA0-1090-000 |
Tension spring - Provides upward tension for the green release lever (2 used) - Mounts in the left and right rear corners of the fusing assembly |
| RA0-1090-000CN |
Tension spring - Provides upward tension for the green release lever (2 used) - Mounts in the left and right rear corners of the fusing assembly |
| RA0-1099-000 |
Torsion spring - Provides a small amount of back pressure for the delivery sensor flag - mounts in the rear center of the fusing assembly |
| RA0-1104-000 |
Roller bushing/retainer - Mounts on the right end of the face-up output roller and retains it in the fusing assembly |
| RA0-1104-000CN |
Mounts on the right end of the face-up output roller and retains it in the fusing assembly |
| RA0-1115-000 |
Torsion spring - Provides pressure for the lower solid rollers on the face-down paper delivery assembly (2 used) |
| RA0-1115-000CN |
Torsion spring - Provides pressure for the lower solid rollers on the face-down paper delivery assembly (2 used) |
| RA0-1116-000 |
Torsion spring - Provides pressure for the upper serrated rollers on the face-down paper delivery assembly (2 used) |
| RA0-1116-000CN |
Torsion spring - Provides pressure for the upper serrated rollers on the face-down paper delivery assembly (2 used) |
| RA0-1127-000 |
Support pan (case) for the print engine controller board - Metal pan which also acts as part of the bottom of the printer |
| RA0-1127-000CN |
Support pan (case) for the print engine controller board - Metal pan which also acts as part of the bottom of the printer |
| RA0-1128-000 |
Printed circuit board spacer - Mounts between the print engine control board and the metal support pan (six used) |
| RA0-1128-000CN |
Printed circuit board spacer - Mounts between the print engine control board and the metal support pan (six used) |
| RA0-1161-000 |
Front guide assembly - Ribbed plastic piece that runs the width of the printer - Mounts to the front of the left and right side plates |
| RA0-1161-000CN |
Front guide assembly - Ribbed plastic piece that runs the width of the printer - Mounts to the front of the left and right side plates |
| RA0-1169-000 |
Compression spring - Provides tension for the shutter lever - Mounts between the shutter lever and the laser/scanner assembly |
| RA0-1169-000CN |
Compression spring - Provides tension for the shutter lever - Mounts between the shutter lever and the laser/scanner assembly |
| RA0-1172-000 |
17 tooth gear assembly - Includes the 17 tooth gear mounted on a black plastic bracket - Mounts to the right side plate assembly |
| RA0-1172-000CN |
17 tooth gear assembly - Includes the 17 tooth gear mounted on a black plastic bracket - Mounts to the right side plate assembly |
| RA0-1173-000 |
Mounting support - Metal piece that supports the paper pick-up solenoid (SL001) - Mounts on the right side plate |
| RA0-1173-000CN |
Mounting support - Metal piece that supports the paper pick-up solenoid (SL001) - Mounts on the right side plate |
| RA0-1175-000CN |
Tension spring - Provides tension for lever - Mounts on the lower front on the right side plate |
| RA0-1176-000 |
69 tooth gear - Large gear with ribs and six small holes - Mounts on on a rod in the upper rear corner of the right side plate |
| RA0-1176-000CN |
69 tooth gear - Large gear with ribs and six small holes - Mounts on on a rod in the upper rear corner of the right side plate |
| RA0-1177-000 |
Front cover - Lower front of printer - With opening for inserting the paper input tray assembly |
| RA0-1177-000CN |
Front cover - Lower front of printer - With opening for inserting the paper input tray assembly |
| RA0-1178-000 |
Right side cover assembly - Has molded-in air intake louvers |
| RA0-1178-000CN |
Right side cover assembly - Has molded-in air intake louvers |
| RA0-1179-000 |
Left side printer cover - Covers the USB and parallel port Connectors (On the formatter board) |
| RA0-1179-000CN |
Left side printer cover - Covers the USB and parallel port Connectors (On the formatter board) |
| RA0-1181-000 |
Guide - For the shutter lever on the laser/scanner assembly - Mounts on the metal support bracket for the laser/scanner assembly |
| RA0-1181-000CN |
Guide - For the shutter lever on the laser/scanner assembly - Mounts on the metal support bracket for the laser/scanner assembly |
| RA0-1182-000 |
Shutter lever - Spring loaded lever - Mounts to the top of the laser/scanner assembly |
| RA0-1182-000CN |
Shutter lever - Spring loaded lever |
| RA0-1183-000 |
Connector cover - Small rectangular plastic cover - Mounts on top of the left side cover (Unused slot) |
| RA0-1183-000CN |
Connector cover - Small rectangular plastic cover - Mounts on top of the left side cover (Unused slot) |
| RA0-1184-000 |
Right side cover mounting support - Front Cover support - Mounts on the upper right corner of the right side plate |
| RA0-1184-000CN |
Front Cover support - Mounts on the upper right corner of the right side plate |
| RA0-1185-000 |
Left side fuser bracket (`L` Shaped) - Provides mounting support for the fusing assembly - Mounts to the upper rear corner of the left side plate |
| RA0-1185-000CN |
Left side fuser bracket (`L` Shaped) - Provides mounting support for the fusing assembly - Mounts to the upper rear corner of the left side plate |
| RA0-1186-000 |
Right side fuser bracket (`L` Shaped) - Provides mounting support for the fusing assembly - Mounts to the upper rear corner of the right side plate |
| RA0-1186-000CN |
Right side fuser bracket (`L` Shaped) - Provides mounting support for the fusing assembly - Mounts to the upper rear corner of the right side plate |
| RA0-1197-000 |
Rubber foot - Used for the front feet on the bottom of the printer - Mounts on the bottom of the right and left side plate assemblies (two used) |
| RA0-1197-000CN |
Rubber foot - Used for the front feet on the bottom of the printer - Mounts on the bottom of the right and left side plate assemblies (two used) |
| RA0-1200-000 |
Torsion spring - Provides high voltage connection to the toner cartridge (primary charging roller) - Mounts on the left rear side of the paper feed guide assembly |
| RA0-1200-000CN |
Torsion spring - Provides high voltage connection to the toner cartridge (primary charging roller) - Mounts behind the transfer roller on the left side of the paper pickup assembly |
| RA0-1212-000 |
Tension spring - Provides tension for the linkage which engages the toner cartridge drive gear - Mounts on the right side plate |
| RA0-1212-000CN |
Tensoin spring - Provides tension for the linkage which engages the toner cartridge drive gear - Mounts on the right side plate |
| RA0-1403-000 |
Left side cover - Has cut-out for the cable pod assembly |
| RA0-1403-000CN |
Left side cover - Has cut-out for the cable pod assembly |
| RA0-1405-000 |
Paper tray cover - Lift-up translucent aqua plastic cover for the input paper tray |
| RA0-1405-000CN |
Paper tray cover - Lift-up translucent aqua plastic cover for the input paper tray |
| RA0-1524-000 |
Mounting plate (stamped sheet-metal plate) - For the formatter PC board - Mounts on the left side plate assembly |
| RA0-1524-000CN |
Mounting plate (stamped sheet-metal plate) - For the formatter PC board - Mounts on the left side plate assembly |
| RA0-1528-000 |
Small insulating sheet (clear plastic) - Protects the formatter board from shorting out - Mounts between the formatter PC board and the mounting plate |
| RA0-1528-000CN |
Small insulating sheet (clear plastic) - Protects the formatter board from shorting out - Mounts between the formatter PC board and the mounting plate |
| RA1-0666-000 |
D-Shaped Pickup Roller - for Cassette Tray Feed (3 Used) |
| RA1-0666-000CN |
D-Shaped Pickup Roller - for Cassette Tray Feed (3 Used) |
| RA1-0667-000 |
Guide Plate - on Sides of Rear Door Rollers (2 Used/Roller) |
| RA1-0667-000CN |
Guide Plate - on Sides of Rear Door Rollers (2 Used/Roller) |
| RA1-0696-000 |
Lower Pressure Roller - Hard Rubber Roller - in Fusing Assy |
| RA1-0696-000CN |
Lower Pressure Roller - Hard Rubber Roller - in Fusing Assy |
| RA1-0697-000KT |
Fusing roller - Hollow roller - Heat lamp goes in its core |
| RA1-0729-030 |
Upper unit release handle (Green) - Press to unlock unit |
| RA1-0729-030CN |
Upper unit release handle (Green) - Press to unlock unit |
| RA1-0861-000 |
Paper stop - For 92285B/C/D/E input paper trays |
| RA1-0861-000CN |
Paper stop - For 92285B/C/D/E input paper trays |
| RA1-0918-000 |
Upper right side panel - Has cutout for toner cartridge door |
| RA1-0918-000CN |
Upper right side panel - Has cutout for toner cartridge door |
| RA1-0919-000 |
Right door - Access door for inserting toner cartridge |
| RA1-0919-000CN |
Right door - Access door for inserting toner cartridge |
| RA1-0921-000 |
Upper Left Side Panel - Opposite of Toner Access Door |
| RA1-0921-000CN |
Upper Left Side Panel - Opposite of Toner Access Door |
|