Internet Marketing Dallas
Printer Parts » Printer Category » C3920A Duplexer Parts
Part Number |
Replacement |
Description |
|||
| RA2-2072-000 | Timing Belt - Between the Two Holding Tray Rollers - Goes on the Left Side of the Paper Holding Area (Under the LaserJet) of the Duplexer | ||||
| RA2-2083-000 | Static Brush - Mounts to the Bottom of the Lower Feed Guide (Towards the Bottom of the Switchback Area of the Duplexer) | ||||
| RA2-2088-000 | Switchback guide - Large ribbed piece in the top of the switchback area of the duplexer | ||||
| RA2-2089-000 | Roller Holder - Pinch Roller Holder - Four Used | ||||
| RA2-2090-000 | Switchback deflector (Shaft with curved deflector fingers) - Attaches to the rear of the switchback guide (in the top of the duplexer) | ||||
| RA2-2093-000 | Pinch Roller - Top of Switchback Guide - 4 Used | ||||
| RA2-2102-000 | Guide Roller - Non-Spring Loaded Rollers on Front of Switchback Guide - Three Used | ||||
| RA2-2112-000 | Cable Cover - Protects Cable on Right Side of Duplexer Switchback Assembly | ||||
| RA2-2118-000 | Paper drive roller (Shaft with four rubber rollers on it) - Mounts in the rear of the switchback area of the duplexer (Rollers extend through cut outs in the rear support frame) | ||||
| RA2-2119-000 | Paper deflector assembly (Shaft with curved deflector fingers) - Attaches to the front of the switchback guide (in the top of the duplexer) - Solenoid activated | ||||
| RA2-2124-000 | Paper drive roller (Shaft with four rubber rollers on it) - Mounts in the top center in the switchback area of the duplexer | ||||
| RA2-2126-000 | Static Brush - Mounts in the Front of the Paper Holding Area (Under the LaserJet) of the Duplexer | ||||
| RA2-2231-000 | Front Cover (L-Shaped) - Small Cover on the Front of the Duplexer (Under the LaserJet) - Has an Arrow on it | ||||
| RA2-2232-000 | Left Cover - Small Cover on the Left Side of the Duplexer (Under the LaserJet) - Viewed from the Front of the Printer | ||||
| RA2-2233-000 | Right Cover - Small Cover on the Right Side of the Duplexer (Under the LaserJet) - Viewed from the Front of the Printer | ||||
| RA2-2237-000 | Lower Rear Cover - Small Cover Under the Switchback Area of the Duplexer | ||||
| RF1-3806-000 | Holding Tray Linkage - Arm Below Gears on Right Side | ||||
| RF1-3808-000 | Switchback Solenoid - Mounts in the Upper Left Corner of the Switchback Area of the Duplexer - Moves Paper Deflector | ||||
| RF1-3811-000 | Paper feed guide - Fits between the upper and lower curved paper guides | ||||
| RF1-3813-000 | Stepper Motor - Mounts in the Upper Right Side in the Switchback Area of the Duplexer | ||||
| RF1-3814-000 | Rear Motor - on the Left Side of the Paper Holding Area (Under the LaserJet) Portion of the Duplexer | ||||
| RF1-3815-000 | Front Motor - on the Left Side of the Paper Holding Area (Under the LaserJet) Portion of the Duplexer | ||||
| RG1-3503-000 | Power Supply Assembly - Small Board in the Bottom Right of the Duplexer | ||||
| RG1-3529-000 | Sensor cable - From controller PCA to photo sensor PS1 | ||||
| RG1-3570-000 | Upper Rear Cover Assembly - Large `Box` Structure on the Rear of the LaserJet (Covering the Switchback Area of the Duplexer) - Includes Paper Reversing Tray (on Top) and Latch | ||||
| RG1-3582-000 | Duplexer Controller Board - Large Board in the Bottom of the Duplexer | ||||
| RH7-1235-000 | Tubeaxial Fan Assembly - Mounts in the Top Rear of the Duplex Switchback Assembly | ||||
| RS1-0586-000 | Reduction Gear (40 Teeth / 24 Teeth) - On the Left Side of the Holding Tray in the Duplexer Assembly (2 Used) | ||||
| RS1-0587-000 | Reduction Gear (24 Teeth / 18 Teeth) - On the Left Side of the Holding Tray in the Duplexer Assembly (2 Used) | ||||
| RS1-0588-000 | Reduction Gear (33 Teeth / 20 Teeth) - On the Left Side of the Holding Tray in the Duplexer Assembly (2 Used) | ||||
| RS1-0589-000 | Roller Drive Gear (22 Teeth) - on the Right Side of the Duplexer Switchback Assembly (2 Used) | ||||
| RS1-0590-000 | Drive Gear (32 Teeth) - on the Right Side of the Duplexer Switchback Assembly (2 Used) | ||||
| RS1-0591-000 | Reduction Gear (39 Teeth / 22 Teeth) - on the Right Side of the Duplexer Switchback Assembly (2 Used) | ||||
| RS1-0592-000 | Reduction Gear (54 Teeth / 29 Teeth) - on the Right Side of the Duplexer Switchback Assembly | ||||
| RS1-0595-000 | Gear/Roller (18 Teeth) - On the Left Side of the Holding Tray in the Duplexer Assembly (4 Used) | ||||
| RS1-2408-000 | Switchback Spring- Provides Tension for Switchback Tray | ||||
| RS1-2410-000 | Deflector spring - Provides tension for duplex paper switchback paper deflector assembly | ||||
| RS1-2411-000 | Roller Holder Spring - Provides Tension for Pinch Roller - Four Used | ||||
| RS1-2412-000 | Deflector Spring - Provides Tension for Switchback Defelctor at Top Back of Duplexer - Four Used | ||||
| RS1-7009-000 | Switchback pin - Pivot point of switchback assembly |
© 1997 - 2008 Jim Catanich - Dallas Internet Marketing Catanich Terms of Use Terms of Sale Privacy Statement Cookies About Contact Press Site Map |